Dishwasher error codes

Check for a slow drain path, blocked filter area, or kinked drain hose before another cycle.

Cancel the cycle and inspect the drain hose, sink connection, and disposal inlet.

Check simple drain restrictions first and stop if water stays in the tub.

Let the dishwasher drain and stop if water enters or overfills again.

Confirm the water supply is open and the inlet path is not restricted.

Check household hot water temperature and stop if heating issues repeat.

Power reset once and request service if C7 returns on a normal cycle.

Clear items blocking the detergent cup and run one short test cycle.

Move dishes away from the dispenser and confirm the detergent cup closes freely.

Check the drain hose, disposer connection, and filter area before retrying.

Stop the cycle, turn off water if leaking is active, and inspect visible door or hose areas.

Reset the control once and confirm the breaker or outlet is stable.

Turn off water if leaking is active, then check around the door, drain hose, and base.

Do not use hand dish soap; clear suds with model-approved steps and use dishwasher detergent only.

Use the documented Control Lock button hold for your model rather than forcing panel buttons.

Stop after one safe reset; fan motor conditions need detailed service inspection.

Avoid repeated heated drying attempts and arrange service if F35 returns.

Check for items blocking the door path and request service if the feature remains stuck.

Run one reset and short test only if water fills and drains normally.

Verify the water valve is open and the inlet hose is not kinked.

Check for items blocking spray arms; service is likely if the code returns empty.

Reorganize dishes that may touch moving spray parts and stop if the code returns empty.

Check the drain hose, sink connection, and filter area for restrictions.

Stop after checking for obvious water-level or leak symptoms; PE normally needs service inspection.

Do not keep resetting the dishwasher; temperature sensor faults usually need service.

Confirm the model type first; clean only the documented filter area or stop for service if unsure.

Remove obstructions from the sump or spray path; service is likely if it returns empty.

Verify the hot water supply is not set too high before running another test.

Confirm the supply valve is open and the inlet hose is not kinked.

Check the drain hose, sink connection, garbage disposal plug, and filter area.

Check for dishes blocking the reflector or spray path.

Run one normal fill test only after checking supply, then stop if 9E returns.

If you are not connecting the dishwasher, turn it off and back on to leave AP mode.

Turn the dishwasher off and check that every button releases normally.

Power reset once and request service if CE continues.

Switch power off briefly, run a controlled empty test, and stop if HC returns.

Do not repeat heated cycles if HE returns; use service for heater or sensor diagnosis.

Turn off water if leaking is active and check around the door, base, and hose connections.

Cancel the cycle and watch for continued filling or draining problems.

Turn the dishwasher off and retry once; repeated PC usually needs service.

Run one empty half-load test only if safe, then request service if PE returns.

Empty the dishwasher and stop repeated tests if tE returns after a reset.

Check for racks or dishes blocking the door and close it firmly.

Confirm the hot water supply is normal; service is likely if heating never recovers.

Clean the filter area and check the drain hose and sink connection before retrying.

Check the filter, drain hose, and household drain for restrictions.

Reset the dishwasher once and stop if the circuit loses power again.

Confirm the water supply is open and the inlet hose is not kinked.

Stop repeated cycles if the wash motor does not run normally or the code returns empty.

Turn off water if leaking is active and inspect around the door and base before resetting.

Check the drain hose, sink connection, and disposal plug before another cycle.

Open the supply valve fully and check for a kinked inlet hose.

Reset power at the breaker once; repeated E01 needs Bosch support or service.

Reset power once and stop if E02 returns, because board faults are service-level.

Power reset once; repeated E03 should go to service rather than repeated cycles.

Do not keep running heated cycles; contact support if E04 remains.

Check for obvious rack or spray blockage, then stop if E05 returns.

Check that the door closes normally and request service if E06 repeats.

Reset power once; repeated E07 is not a homeowner repair step.

Reset once; if it returns, stop repeating heated cycles and arrange service.

Avoid repeated heat-dry tests and contact support if E10 returns.

Use the model-approved descaling path and check water-softener salt guidance if equipped.

Check water supply first; service is likely if supply is normal.

Turn off water if leaking is active and check for visible leaks before resetting.

Check the inlet hose for kinks or damage and confirm the supply is on.

Check inlet hose condition and stop if the filling code returns after supply is normal.

Open the supply valve fully and inspect the inlet hose.

Power reset once; repeated E19 should be handled by service.

Do not force repeated cycles if the pump hums or the code returns immediately.

Reset power once and contact support if E21 returns.

Clean and reseat the dishwasher filter, then run a short rinse cycle.

Check simple drain restrictions first; repeated E23 usually needs service.

Check the filter, drain hose, sink air gap, and disposal connection.

Clean the filter and inspect the pump cover only as the manual allows.

Avoid repeated starts and have the outlet or circuit checked if it repeats.

Check racks and dishes near the door, then close the latch firmly.

Confirm hot water supply and stop if the dishwasher never reaches wash temperature.

Clean the filter area and inspect the drain hose or sink connection before retrying.

Check the dishwasher filter, drain hose, and household drain path.

Reset the dishwasher once and stop if the power fault repeats.